scholarly journals Three‐dimensional numerical modeling of thermal regime and slab dehydration beneath Kanto and Tohoku, Japan

2017 ◽  
Vol 122 (1) ◽  
pp. 332-353 ◽  
Author(s):  
Yingfeng Ji ◽  
Shoichi Yoshioka ◽  
Vlad Constantin Manea ◽  
Marina Manea ◽  
Takumi Matsumoto
Keyword(s):  
Numerical Modeling ◽  
Thermal Regime ◽  
Three Dimensional ◽  
Slab Dehydration

Novel three-dimensional multi-objective numerical modeling for hot strip tandem rolling

2021 ◽  
Author(s):  
Lianjie Li ◽  
Jianxin Li ◽  
Haibo Xie ◽  
Hongqiang Liu ◽  
Li Sun ◽  
...  
Keyword(s):  
Numerical Modeling ◽  
Three Dimensional ◽  
Multi Objective ◽  
Hot Strip

Three-Dimensional Numerical Modeling of Convective Heat Transfer During Shallow-Depth Forced-Air Drying of Brown Rice Grains

2015 ◽  
Vol 33 (11) ◽  
pp. 1350-1359 ◽  
Author(s):  
Jonathan H. Perez ◽  
Fumina Tanaka ◽  
Fumihiko Tanaka ◽  
Daisuke Hamanaka ◽  
Toshitaka Uchino
Keyword(s):  
Heat Transfer ◽  
Numerical Modeling ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Three Dimensional ◽  
Brown Rice ◽  
Shallow Depth ◽  
Air Drying ◽  
Rice Grains ◽  
Forced Air

Spreadsheet Tool for Quick-Turn 3D Numerical Modeling of Package Thermal Performance With Non-Uniform Die Heating

2001 ◽  
Author(s):  
Abhay A. Watwe ◽  
Ravi S. Prasher
Keyword(s):  
Finite Element ◽  
Numerical Modeling ◽  
Finite Volume ◽  
Thermal Performance ◽  
Three Dimensional ◽  
3D Numerical Modeling ◽  
Conventional Analysis ◽  
Time Required ◽  
The Impact ◽  
Fourier Equation

Abstract Traditional methods of estimating package thermal performance employ numerical modeling using commercially available finite-volume or finite-element tools. Use of these tools requires training and experience in thermal modeling. This methodology restricts the ability of die designers to quickly evaluate the thermal impact of their die architecture due to the added throughput time required to enlist the services of a thermal analyst. This paper describes the development of an easy to use spreadsheet tool, which performs quick-turn numerical evaluations of the impact of non-uniform die heating. The tool employs well-established finite-volume numerical techniques to solve the steady-state, three-dimensional Fourier equation of conduction in the package geometry. Minimal input data is required and the inputs are customized using visual basic pull-down menus to assist die designers who may not be thermal experts. Data showing comparison of the estimates from the spreadsheet tool with that obtained from a conventional analysis using the commercially available finite element code ANSYS™ is also presented.

scholarly journals Numerical modeling of the hydraulic impact of riparian vegetation

2018 ◽  
Vol 44 ◽  
pp. 00194
Author(s):  
Krzysztof Wolski ◽  
Tomasz Tymiński ◽  
Grzegorz Chrobak
Keyword(s):  
Numerical Modeling ◽  
Riparian Vegetation ◽  
Water Surface ◽  
Numerical Models ◽  
Three Dimensional ◽  
Careful Examination ◽  
Impact Structure ◽  
Hydraulic Impact ◽  
Vegetation Zones ◽  
Maximal Shear Stress

This paper presents results of numerical modelling of riverbed segment with riparian vegetation performed with use of CCHE2 software. Vegetation zones are places where dynamic of water flow increases. Therefore, there is a need of careful examination of hydraulic impact structure of such zones. Accurate research is necessary and should be performed with use of physical or numerical models, two or three dimensional. Paper presents distribution of velocity and area of water surface for two variants of vegetation deposition acquired in CCHE2D software and modelled for riverbed with distinctive riparian vegetation. Results point to significant (30–40%) increase of maximal velocities in riverbed with riparian vegetation, while directly near the vegetation there were zones with very low velocities. Local damming occurs before vegetal zone. Maximal shear stress in zones with increased velocity is significantly augmented compared to conditions with no vegetation, which can cause more intensive erosion in those zones

Three-dimensional numerical modeling of cohesive sediment transport and wind wave impact in a shallow oxbow lake

2008 ◽  
Vol 31 (7) ◽  
pp. 1004-1014 ◽  
Author(s):  
Xiaobo Chao ◽  
Yafei Jia ◽  
F. Douglas Shields ◽  
Sam S.Y. Wang ◽  
Charles M. Cooper
Keyword(s):  
Numerical Modeling ◽  
Sediment Transport ◽  
Wind Wave ◽  
Three Dimensional ◽  
Cohesive Sediment ◽  
Oxbow Lake ◽  
Wave Impact ◽  
Cohesive Sediment Transport
Sign in / Sign up

Export Citation Format

Share Document