Evolution of soil wetting patterns preceding a hydrologically induced landslide inferred from electrical resistivity survey and point measurements of volumetric water content and pore water pressure

2013 ◽  
Vol 49 (12) ◽  
pp. 7992-8004 ◽  
Author(s):  
Peter Lehmann ◽  
Francesca Gambazzi ◽  
Barbara Suski ◽  
Ludovic Baron ◽  
Amin Askarinejad ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Volumetric Water Content ◽  
Electrical Resistivity Survey ◽  
Resistivity Survey ◽  
Soil Wetting

scholarly journals Laboratory Experiment and Numerical Analysis on the Precursory Hydraulic Process of Rainfall-Induced Slope Failure

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Joon-Young Park ◽  
Young-Suk Song
Keyword(s):  
Numerical Modeling ◽  
Laboratory Test ◽  
Water Content ◽  
Pore Water ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Volumetric Water Content ◽  
Wetting Front ◽  
Artificial Rainfall

A combined analysis involving a laboratory test and numerical modeling was performed to investigate the hydraulic processes leading to slope failure during rainfall. Through a laboratory landslide test in which artificial rainfall was applied to a homogeneous sandy slope, the timing and configurations of multiple slides were identified. In addition, volumetric water content was measured in real time through the use of monitoring sensors. The measured volumetric water content data were then used to validate the relevance of the numerical modeling results. The validated numerical modeling of the laboratory-scale slope failures provided insight into the hydraulic conditions that trigger landslides. According to the numerical modeling results, the miniaturized slope in the laboratory test was saturated in a manner so that the wetting front initially progresses downward and then the accumulated rainwater at the toe of the slope creates a water table that advances toward the crest. Furthermore, each of the five sequential failures that occurred during this experiment created slip surfaces where the pore-water pressure had achieved full saturation and an excessive pore-water pressure state. The findings of this study are expected to help understand the hydraulic prerequisites of landslide phenomena.

A novel vegetated three-layer landfill cover system using recycled construction wastes without geomembrane

2019 ◽  
Vol 56 (12) ◽  
pp. 1863-1875 ◽  
Author(s):  
Charles W.W. Ng ◽  
R. Chen ◽  
J.L. Coo ◽  
J. Liu ◽  
J.J. Ni ◽  
...  
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Volumetric Water Content ◽  
Cover System ◽  
Landfill Cover ◽  
Decomposed Granite ◽  
Landfill Cover System ◽  
Completely Decomposed Granite

To promote environmental protection and sustainability, the use of plants and recycled wastes in geotechnical construction such as landfill covers is recommended. A landfill cover field test was conducted at the Shenzhen Xiaping landfill site, located in a humid climatic region of China. The main objective was to validate the field performance of a novel vegetated three-layer landfill cover system using recycled construction waste without the need of geomembrane. Unsieved completely decomposed granite and coarsely crushed concrete was used for the top and intermediate layers while sieved completely decomposed granite was used as the lowest layer. One section was transplanted with Bermuda grass while the other section was left bare. To assess the landfill cover performance, pore-water pressure, volumetric water content, percolation, and atmospheric parameters were measured for a period of 13 months under natural climatic conditions. The cumulative rainfall depth was about 2950 mm over the entire monitoring period. During rainfall, the presence of grass led to lower pore-water pressure (or higher suction) and volumetric water content in the three-layer landfill cover system. At the end of monitoring, the cumulative percolation was about 27 and 20 mm for the bare and grass-covered landfill covers, respectively. It is evident that the vegetated three-layer landfill cover system using recycled concrete without geomembrane can be effective in minimizing percolation in humid climates.

Experimental study on dual capillary barrier using recycled asphalt pavement materials

2014 ◽  
Vol 51 (10) ◽  
pp. 1165-1177 ◽  
Author(s):  
F.R. Harnas ◽  
H. Rahardjo ◽  
E.C. Leong ◽  
J.Y. Wang
Keyword(s):  
Water Content ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Storage ◽  
Pressure Head ◽  
Volumetric Water Content ◽  
Capillary Barrier ◽  
Recycled Asphalt ◽  
Fine Grained ◽  
Drainage Rate

The performance of a capillary barrier cover as a cover system is affected by the ability of the capillary barrier to store water. To increase the water storage of a capillary barrier cover, the dual capillary barrier (DCB) concept is proposed. The objective of this paper is to investigate the water storage of the proposed DCB as compared to the storage of a traditional single capillary barrier (SCB). The investigation is conducted using two one-dimensional infiltration column tests under different rainfall conditions. The results show that a DCB stores more water as compared to SCB. The results show that the fine-grained layers of a DCB have higher volumetric water contents during drainage as compared to that of the fine-grained layer of an SCB. The higher volumetric water content is caused by the fact that the thickness of the layers in a DCB corresponds to a pore-water pressure head range where the material has the highest volumetric water content. In addition, a slower drainage rate is resulted from additional layering in a DCB.

scholarly journals Field Test Research on Red Clay Slope under Atmospheric Action

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Kaisheng Chen
Keyword(s):  
Internal Friction ◽  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Red Clay ◽  
Failure Characteristics ◽  
Clay Slopes

By embedding water content sensors and pore water pressure sensors inside the red clay slope on-site in Guiyang, Guizhou, shear tests were performed on soil samples at different depths of the slope under different weather. The changes of water content, pore water pressure, and shear strength index of the slope inside the slope under the influence of the atmosphere were tracked and tested, and the failure characteristics and evolution of the red clay slope were analyzed. It is believed that the depth of influence of the atmosphere on red clay slopes is about 0.7 m, rainfall is the most direct climatic factor leading to the instability of red clay slopes, and the evaporation effect is an important prerequisite for the catastrophe of red clay slopes. The cohesion and internal friction angle of the slope soil have a good binary quadratic function relationship with the water content and density. The water content and density can be used to calculate the cohesion and internal friction angle. Failure characteristics of red clay slopes: the overall instability failure is less, mainly surface failure represented by gullies and weathering and spalling, and then gradually evolved into shallow instability failure represented by collapse and slump. The damage evolution law is as follows: splash corrosion and surface corrosion stage⟶ fracture development stage⟶ gully formation stage⟶ gully development through stage⟶ local collapse stage⟶ slope foot collapse stage.

Aspects of the behaviour of compacted clayey soils on drying and wetting paths

2002 ◽  
Vol 39 (6) ◽  
pp. 1341-1357 ◽  
Author(s):  
Jean-Marie Fleureau ◽  
Jean-Claude Verbrugge ◽  
Pedro J Huergo ◽  
António Gomes Correia ◽  
Siba Kheirbek-Saoud
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Dry Density ◽  
Clayey Soils ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

A relatively large number of drying and wetting tests have been performed on clayey soils compacted at the standard or modified Proctor optimum water content and maximum density and compared with tests on normally consolidated or overconsolidated soils. The results show that drying and wetting paths on compacted soils are fairly linear and reversible in the void ratio or water content versus negative pore-water pressure planes. On the wet side of the optimum, the wetting paths are independent of the compaction water content and can be approached by compaction tests with measurement of the negative pore-water pressure. Correlations have been established between the liquid limit of the soils and such properties as the optimum water content and negative pore-water pressure, the maximum dry density, and the swelling or drying index. Although based on a limited number of tests, these correlations provide a fairly good basis to model the drying–wetting paths when all the necessary data are not available.Key words: compaction, unsaturated soils, clays, drying, wetting, Proctor conditions.

Experimental verification of the theory of consolidation for unsaturated soils

1995 ◽  
Vol 32 (5) ◽  
pp. 749-766 ◽  
Author(s):  
Harianto Rahardjo ◽  
Delwyn G. Fredlund
Keyword(s):  
Water Content ◽  
Pore Pressure ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Matric Suction ◽  
Water Volume ◽  
Loading Tests ◽  
Undrained Loading

An experimental program was designed to study the behavior of unsaturated soils during undrained loading and consolidation. A Ko cylinder was designed and built for the testing program. Simultaneous measurements of pore-air and pore-water pressures could be made throughout a soil specimen using this Ko cylinder. Four types of tests were performed on a silty sand. These are (1) undrained loading tests where both the air and water are not allowed to drain, (2) constant water content tests where only the water phase is not allowed to drain, (3) consolidation tests where both the air and water phases are allowed to drain, and (4) increasing matric suction tests. Undrained loading tests or constant water content loading tests were conducted for measuring the pore pressure parameters for the unsaturated soil. Drained tests consisting of either consolidation tests or increasing matric suction tests were conducted to study the pore pressure distribution and volume change behavior throughout an unsaturated soil during a transient process. The experimental pore pressure parameters obtained from the undrained loadings and constant water content leadings agreed reasonably well with theory. The pore-air pressure was found to dissipate instantaneously when the air phase is continuous. The pore-water pressure dissipation during the consolidation test was found to be faster than the pore-water pressure decrease during the increasing matric suction test. The differing rates of dissipation were attributed to the different coefficients of water volume change for each of the tests. The water volume changes during the consolidation test were considerably smaller than the water volume changes during the increasing matric suction tests for the same increment of pressure change. Key words : consolidation, Ko loading, matric suction, pore-air pressures, pore-water pressures, unsaturated soils

scholarly journals Discussion on the Characteristics of Seismic Signals Due to Riverbank Landslides from Laboratory Tests

Water ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 83
Author(s):  
Zheng-Yi Feng ◽  
Chia-Ming Hsu ◽  
Shi-Hao Chen
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Levels ◽  
Seismic Signals ◽  
Transform Method ◽  
Frequency Distributions ◽  
Landslide Event ◽  
Self Potential

Floods and erosion often cause landslides of riverbanks and induce problems such as river blockage, shift of river center, or flooding from rising riverbeds. Instrumentation and monitoring are often used to explore landslide and erosion behavior of riverbanks. Therefore, this study identified landslide types and characteristics of their seismic signals due to toe erosion of riverbanks through riverbank models with various instrumentation sensors in a laboratory flume. To induce landslides in the riverbank model, a test was set up for water to flow through the toe of the riverbank model. Seismic signals of each landslide event were measured during the tests with accelerometers. Nonpolarized electrodes were installed for observing the self-potential changes during the test. Water content and pore water pressure gauges were installed in the riverbank model. In addition, water levels were recorded. The Hilbert–Huang transform method was used to analyze the characteristics of seismic signals caused by water flow and riverbank landslides. Time points, landslide frequency distributions, and the characteristics of several landslide events in the riverbank models were estimated using the seismic signals. This study identified three types of landslides: single, intermittent, and successive. Moreover, changes in self-potential signals, pore water pressure, and water content during the tests were examined and were found to correspond to the landslide process of the riverbank model.

Determining Range of Saturated Ground around Leakage Pipeline Using Unsteady Seepage Numerical Analysis

2012 ◽  
Vol 204-208 ◽  
pp. 609-613
Author(s):  
Xing Gao Li ◽  
Chao Jie Duan
Keyword(s):  
Numerical Analysis ◽  
Hydraulic Conductivity ◽  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Injection Well ◽  
Exponential Relationship ◽  
Seepage Analysis ◽  
Conductivity Function

It is of great significance to estimate the range of saturated ground around leakage pipelines when tunneling near the pipelines. The range of saturated ground can be determined from the distributions of the water content and pore-water pressure in ground around the leakage pipelines. The leakage pipeline being modeled as an injection well, a series of unsteady seepage numerical analysis is performed to understand the effects of the internal water pressure of pipelines on the range of saturated ground surrounding the pipelines, and computation results show the exponential relationship between them. In the unsteady seepage analysis, the hydraulic conductivity function and the volumetric water content function must be determined beforehand to get reasonable results of the range of saturated ground.

Response of a residual soil slope to rainfall

2005 ◽  
Vol 42 (2) ◽  
pp. 340-351 ◽  
Author(s):  
H Rahardjo ◽  
T T Lee ◽  
E C Leong ◽  
R B Rezaur
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Residual Soil ◽  
Soil Slope ◽  
Pore Water Pressures ◽  
Pressure Water ◽  
Water Contents ◽  
Residual Soil Slope

Rainfall-induced landslides are a common problem in residual soil slopes of the tropics. It is widely known that rainfall-induced slope failures are mainly caused by infiltration of rainwater; however, the response of a residual soil slope to infiltration is not fully understood. The difficulties lie in the quantification of the flux boundary condition across the slope surface with respect to infiltration and its effect on the pore-water pressure conditions in the slope. Therefore, it is important to understand the response of a slope to different rainfall conditions and the resulting changes in pore-water pressures and water contents. A residual soil slope in Singapore was instrumented with pore-water pressure, water content, and rainfall measuring devices, and studies were carried out under natural and simulated rainfalls. Results indicate that significant infiltration may occur in a residual soil slope during a rainfall. Small total rainfalls can contribute a larger infiltration percentage than large total rainfalls. The percentage of infiltration usually decreases with increasing total rainfalls. The study has indicated the existence of a threshold rainfall of about 10 mm for runoff generation to commence. Infiltration during wet periods may lead to the development of positive pore-water pressures as a consequence of a perched water table condition. Matric suctions are recovered gradually during dry periods due to redistribution. Soil water contents tend to be higher near the toe of the slope than at the crest irrespective of rainfall events, indicating subsurface movement of water in the downslope direction. The study has also indicated a correlation between rainfall amount and relative increase in pore-water pressure. The results can be used to quantify the flux boundary conditions required for the seepage analyses associated with rainfall-induced slope failures.Key words: infiltration, pore-water pressure, water content, residual soil, rainfall-induced slope failures.

Sign in / Sign up

Export Citation Format

Share Document